EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D. EKC B Controller with two relay outputs, extra temperature sensor and digital EN and EN , A2 Weight = g Danfoss can accept no.
|Published (Last):||3 March 2008|
|PDF File Size:||2.41 Mb|
|ePub File Size:||12.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Either with r12 or a DI-input S Normal display Normal display shows the temperature value from the thermostat sensor Sair. Lower alarm limit Here you set when the alarm for low temperature is to start. Sensor error on Sair E Alarm will be given when the input is short-circuited. The limit value will also be raised in connection with reference displacement r But before you change the value, you must have access to the menu.
The function delays the interval time d03 by the set number of minutes, but it only does it once, and this at the very first defrost taking place when voltage is connected to the controller.
Instead of the compressor a solenoid valve may of course be connected in the liquid line. The time delay is set in minutes.
HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102D 084B8506 for Freezer
If the function is controlled by a signal at the DI input, the relevant status can be seen here in the menu. Providing personal data is voluntary, but necessary for providing a reply. Temperature signal 2 can be used for defrost stop based on temperature or for product sensor. There is no alarm delay. The relay is cut out during normal operation and cuts in in alarm situations and when the controller is dead de-energised Refrigeration 2.
Select your own number. Here you define which: The alarm will not become active until the set time delay has been passed. After two seconds you can move back into the mennu again and check whether the copying was danfss. Defrost on demand — aggregate refrigeration time Set here is the refrigeration time allowed without defrosts.
When copying has started the display returns to o Normal function where the relay cuts in when refrigeration is demanded 1: Temperature, time, operating environment, parameter codes, alarms and fault codes are displayed Screen read, long-life relay, lower maintenance costs, easy to restore factory settings EKC and are used for Temperature control Compressor control Fan motor control Defrost control Alarm signalling.
The controller will register when the input is reopened.
Time delay for door alarm The time delay is set in minutes. Carton box Delivery Time: Basic temperature control, precise ekd Up to 3 relay outputs: High temperature alarm A2: Easy product returns Buy a product and check it in your danfosd time, at home. OFF-time in minutes Time delay for couplings of two compressors Settings indicate the time that has to elapse from the first relay cuts in and until the next relay has to cut in.
Refrigeration stopped because of open DI input S Defrost stop temperature The defrost is stopped at eoc given temperature which is measured with a sensor the sensor is defined in d The function is not active during a defrost or start-up after a defrost.
Here you set how large a slide of the S5 temperature can be allowed.
Controller for temperature control – EKC Manual |
Hermetic Compressors c02 min. Push the middle button until the temperature value is shown 2. A-model for simple regulation B-model where an alarm function and possibly also a digital input will be required C-model where the defrost temperature also enjoys top priority D-model with fan function, change-over between temperature reference and case cleaning function All these four controllers are without data communication. Manual control of outputs S Pyskowicka 24, Zabrze in the scope necessary for drawing up and sending a reply to my eic, which was sent to the administrator by the above contact form.
We also inform you that: To rate this product or to add a new review, you need to log in. A special moulding technique unites the hard front plastic, the softer buttons and the seal, so that they become an integral part of the front panel. The setting will be the defrost time if d10 is selected to be 0 EKC c30 d01 d02 d03 d04 Time staggering for defrost cutins during start-up The function is only relevant if you have several refrigeration appliances or groups where you want the defrost to be staggered in relation to one another.
See the significance in the Fault Message section. Sensor error on Saux When copying settings to or from a copying key with functions o65 or o66, the following information may appear: When the input is open it signals that the door is open.
This timer function can be used as a simple way of starting defrosts, but it will always act as safety defrost if one of the subsequent defrost starts is not received.