ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
|Published (Last):||12 December 2014|
|PDF File Size:||19.92 Mb|
|ePub File Size:||20.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
The minimum cladding thickness for shear testing shall be 0.
Users of this standard are expressly advised a2265 determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Chemical analysis may be accomplished by wet chemical or instrumental procedures. The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition. A — 09 Standard Speci?
Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci? NOTE 2—Punch marks for measuring elongation after fracture shall be made on the?
A number in parentheses indicates the year of last reapproval. The base metal shall q265 carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. In reducing the thickness of the specimen, both the alloy 3 Metric Equivalents in. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
ASTM A265 GR 1 titanium alloy strip sheet plate
The steel shall be made by the open-hearth, electric furnace asmt separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes. These bend tests shall be made in the manner of the tension tests indicated in Fig.
A list asrm standardized supplementary requirements for use at the option of the purchaser are included in Speci? If spectrometric procedures are used, the sample shall be exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal. Current edition approved May 1, Astn International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
When none has been astmm Materials and Manufacture 5. Link to Active This link will always route to the current Active version of the standard. Such requirements may include, but are not limited to the following: ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Other tests may be performed by agreement between the supplier and the purchaser. Astj May 1, Historical Version s – view previous versions of standard Translated Version s: The shear test, when speci?
Historical Version s – view previous versions of standard.
ASTM A265 Clad Plate
The properties thus determined shall meet all of the tensile test requirements for the base steel. The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.
Number of Tests and Retests 8. Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Originally approved in The reduced section shall have a gradual taper from the ends toward the center, with the ends 0.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
ASTM A GR 1 titanium alloy strip sheet plate
Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1? This standard has been approved for use a2665 agencies of the Department of Defense.
Specify whether applicable to the cladding alloy, backing steel, or both see Section Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The material shall be cleaned and sufficient millings taken to represent the full cross-section of the remainder. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.
If the requirements of this speci? The base metal shall conform to the chemical requirements of the speci? The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding.